Wedge Innovations SmartLevel El manual del propietario descargar pdf (Pagina 12)

SmartLevel

Maintenance

SmartLevel

is

designed

for the

rugged

construction

environ-

ment,

and the

following

tips

will

ensure

that

your

SmartLevel

is

kept

in top

condition.

•

The

Sensor

Module

and

rails

are

weather-

and

water-resistant. Should

your

SmartLevel

be

splashed with mortar

or

other construction site

residue,

simply wipe clean with

a

damp cloth.

DO

A/OHMMERSE

THE

SENSOR

MODULE

IN

WATER.

•

Aluminum surfaces

can be

cleaned with

a

non-abrasive cleansing

powder.

• ABS

composite surfaces

should

be

cleaned with

a

mild

liquid soap

and

water.

• We

advise

you to

store

your SmartLevel away from extreme temperatures

below

-20°C

(-4°F)

or

higher

than

60°C

(140°F).

•

Don't forget

to

RESET

your SmartLevel daily,

and to use the

simple

"end-

for-end"

test frequently

to see if

SUPERSET

is

required.

QUESTIONS?

PROBLEMS?

Feel free

to

call

us at

1-800-SMARTLEVEL

(762-7853)

Troubleshooting

Guide

Problem

Reason

Solution

SmartLevel

does

not

turn

on.

Battery dead

or

battery

connections

are not

tight

or

have

become disengaged.

Check

battery connections.

See

Battery,

page

19.

SmartLevel does

not

auto-

matically

shut

off

after

five

minutes.

Sensor

Module

is

being

moved

or

jostled.

Keep

unit stationary

for

five

minutes

or

more;

or

turn mod-

ule off

using

On/Off

button.

SmartLevel does

not

measure

accurately.

SmartLevel

has not

been

re-

calibrated

recently,

or has not

been

recalibrated

correctly.

See

Reset Button, pages

7-11

and

follow appropriate Reset

and

SuperSet steps closely.

Reset

button does

not

work.

Not

pressing

Reset

button

for

a

sufficient time.

Push

Reset

button down

until

the

display reading changes.

See

Reset

Button, pages 7-8.

Difficult

to

select desired

mode

or

range setting.

Mode

or

Hold/Range button

is

being pressed

too

long.

Release

button

as

soon

as

desired

setting appears.

See

Mode Button, page 5-6;

or

Hold/Range

Button,

pages

12-13.

Display

reading "jumps"

or

changes

too

easily.

SmartLevel

is set on a

too-

sensitive range setting.

Use

the

Hold/Range

button

to

set a

less-sensitive range

setting.

See

Hold/Range

Button, pages

12-13.

Display

keeps flashing.

The

Reset

button

has

accidentally been pressed.

Press

the

Reset

button again

or

turn SmartLevel

off.

Repeat

the

Reset

procedure.

Display

reads "ERR"

or

"CAL".

Software

diagnostics code Turn

the

module

off, then

on.

If

display continues

to

read

"ERR"

or

"CAL", replace bat-

tery.

If

display still continues

to

read "ERR"

or

"CAL",

call

SmartLevel

Customer Service

at

1-800-762-7853.

3j';0"

SilCKS

Dirt lodged between

button

and

Sensor

Module

housing.

Hold module with display fac-

ing

downward. Press button

repeatedly

to

dislodge dirt.

Module

slips

out of the

rail. Cams

are not

turned

to

properly lock

the

rail.

See

Transferring

the

Sensor

Module between Rails, pages

17-18,

and

follow

the

steps

closely.

Module cannot

be

removed

or

Cams

are not

properly

difficult

to

remove from rail. positioned.

See

Transferring

the

Sensor

Module between Rails, pages

17-18.

and

follow

the

steps

closely.

Dirt lodged between Sensor

Module

and

rail.

Take

fine-gauge wire

and run

it

between module

and

rail

to

remove

dirt.

Battery

compartment cover Screws

not

completely

does

not

come off. disengaged.

Unscrew more thoroughly.

Follow

procedures

under

Battery,

page

19.

20

SmartLevel Maintenance

Troubleshooting Guide

1 2 ... 7 8 9 10 11 12 13

Comentarios a estos manuales

Sin comentarios